How to Repair Dripping Shower Head
Click Here to Call 778-800-2732
It is not fun to take a shower when the water ripples just as if to itself. Some women no longer have the ability to wash their hair with little water - cleaning performance is lacking. What to do? There are several reasons why the shower head does not provide a stronger jet of water.
If the shower head drips, the water pressure is prevented. This can be caused on the one hand by calcium deposits. But even a valve can prevent more water from flowing through the nozzles. With simple means, the cause can often be eliminated quickly.
In most cases, the water pressure increases with some tricks again, because here there are simple solutions on how to repair dripping shower head.
The shower head is calcified
Calcification is the number one cause when the shower drips. In most cases, the nozzles are calcified, therefore clogged. Especially in areas where water is particularly calcareous, this can happen frequently. Because lime is deposited everywhere and water can not flow without obstacles.
In this case, it usually helps to descale the shower head. The pharmacies here have various means on the shelf that help. Thus, the shower head can be removed and placed in a decalcifying solution purchased for several hours. But also citric acid and vinegar do a good job.
It is important to rinse the shower head thoroughly before reinstalling it in the shower. Due to decalcifying acids residues to the enamel coating of a shower or bathtub attack.
Flow limiter in the shower head or tube
If the shower head purchased again and again can not be scaled up? Then check if a flow limiter is installed in the shower head. Some models also have a sliding hook to adjust this and also to decide the amount of water. In other models it is well integrated and not adjustable. So it only helps replacing the shower head. Sometimes, however, the flow limiter can also be easily removed.
But this flow limiter can also be installed in the tube. In some cases, it is directly at the outlet of the hot water tank or on the water heater. But even a butterfly valve on the memory is conceivable. Check here too if you do not see anything in the shower itself. Found? Then do it, if possible, so that one is until you reach the desired water pressure from the shower head.
If the shower head drips only, but the cause can also be found in the tube, because it is not infrequently clogged or calcified. You can easily find out by removing it and checking the water pressure directly from the tap. Then connect the pipe without a shower head. Is it just a drip? So something in the tube prevents water from flowing strongly.
In most cases it is possible to clean a pipe. For descaling, it must also be immersed in a descaling solution. Limescale deposits on the outer skin often dissolve in the grooves, so the tube often looks like new again.
In some cases the descaling of the pipe and the shower head no longer helps. Wear will reach all parts. If they are too old, new copies were better on the market to buy and connect
The reason for a dripping shower head, but it can also be lower. Precisely in areas with hard water, limescale can accumulate in the pipes and restrict them. The result is that less water ever comes out of the tap. You can easily check it by unscrewing the pipe and opening the tap.
Suspicious piping built behind the problem? Then you should consult a specialist. Because the pipes are something for the installer and do not belong to the hands of the laity.
The valves are damaged
If the diverter valve drips, a thorough cleaning will help. Again, lime is often the trigger for unwanted dripping. For cleaning, the handle of the faucet can be unscrewed. Thus, the diverter valve is exposed and can be carefully unscrewed. Now the valve can be cleaned with clear vinegar and a brush. If the diverter valve has cracks, it should be replaced.
Look for mineral deposits that may cause leaks
Hard water, mineral-rich water can often clog your shower head. This can leave deposits in the pipes and cause excessive pressure and leaks.
To clean your shower head and remove mineral deposits , simply remove it. Dip it in a bath of white vinegar.
Leave it in the vinegar for a whole day. This will detach the mineral deposits and accumulation. Remove the shower head from the mixture and manually wipe off the remaining mineral remains.
You can screw it on the pipe in your shower and test the flow. Water should flow a lot better and leaks should disappear.
It can also happen that the shower head drips after use. This is due to the accumulated water that runs out when the shower head is hung back into its holder. Here it helps to shake the shower head after use until no more water drips out.
Another cause could be contamination of the holes of the shower. Straight lime clogs the small holes. The shower head should be decalcified regularly to prevent the problem.
Replace the seals regularly
To prevent a dripping shower head, it is advisable to check the seals regularly and to replace them if necessary. Thus, unwanted dripping can be prevented in advance.
Call a plumber
If replacing older parts and cleaning your shower head do not work, something more serious may be happening. If there is a lot of water escaping from the shower head or if the problem gets worse after you have tried to repair it, you have to call your plumber in Langley.
A dripping shower head is not only on the nerves, so a leak is also right in the money. The water drips unused through the drain. Anyone who picks up a plumber will reach into his pocket again. To solve the problem, the shower head can be easily replaced. In the trade or on the Internet today are various affordable models to get